Latest sample galleries
Latest in-depth reviews
The Everyday Sling might just be the perfect pack for not carrying too much gear, combining comfort with Peak Design's signature modern style.
My model looked at me like I was crazy when we drove to a grimy alleyway behind an Italian grocer because I wanted to shoot 'a pretty summertime editorial look'. While I can hardly blame her, I live and work in Seattle, which can certainly live up to its overcast and rainy stereotype. So, I sometimes find myself in a certain mania to use the sun while it's out.
In this article, I'll walk through a quick and simple look where minimal lighting and a bit of color were used to turn our spot in the grocer's alley into a fashionable set - no studio required. In particular, we will look at how the shot was built up to allow creative control in a mixed-lighting situation, using a combination of external flash and available light.
The model fixing her hair.
There were a few challenges for this shoot. The location was certainly not 'naturally beautiful'. I was shooting in a sedan, which is a fairly constrained space. It was late afternoon. As daylight time was short and I didn't have an assistant with me, the lighting equipment needed to be simple and easy to set up.
|As locations go, this is about as un-glamorous as they get.|
Why this particular location, sandwiched between a dumpster and a crooked cyclone fence? To build up this look, I wanted to start with 'open shade' - a location that was open to the sky but not in direct sunlight. This gives the background a soft, even light. This was important because I was using external flashes as the main light source; having even light in the background meant that I could set my exposure without worrying about blowing out parts of the background scene.
I was also planning on shooting with a wide aperture to allow the background to blur nicely. The fence, when shot out-of-focus, would provide a fairly interesting visual texture, and the rest of the alley wasn't even going to be in the shot. Most importantly, however, this alley is not a high-traffic location, so I would be able to set up the car and lighting without disturbing anybody or getting passers-by in the photos.
|This is a test shot showing the look using only available light with no |
f2.5, 1/80 @ ISO 200.
In the image above note the difference in exposure between the model's arm, which was near the window, and her face, which was in the full shadow of the car. This would be difficult to adjust for without external lighting. Ideally, aside from edge lighting, the model's face would be as bright or brighter than the parts of her body that are in the background. If I hadn't augmented the available light with an artificial light source, the images would be very soft and flat, as in this example. Recall that I was shooting inside a sedan that itself was in open shade. This is an environment with very diffuse, low-contrast light. By the same token, however, this provided an excellent palette for constructing my own lighting setup.
To maximize the effect of the available light and throw the background out of focus, I was shooting with a very wide aperture, f2.5. This can be dangerous territory when photographing people. At f2.5, depth-of-field gets very shallow, particularly for subjects that are close to the camera. Slight movements by the model or the photographer can be enough to throw off critical focus. However, as this was a candid and fairly casual look - one that probably wouldn't be printed at 24 plus inches and hung in a gallery - coming away with something less than an absolutely tack-sharp image was not going to be a deal-breaker.
Metz Mecablitz CT 60-4 flash units. The unit on the right has the built-in diffuser panel in place.These flash units are each about 10 inches (25.5 cm) tall; a good bit larger than an SB or EX class speedlight. They are powered by lead-acid batteries (lower-left, in case.) This is not exactly a lightweight setup, but it's certainly more portable than cases full of studio strobes and softboxes.
My lighting kit for this shoot was a pair of Metz Mecablitz 60 CT-4 flashes that I had borrowed from an assistant. This is a 2000's era flash system which has some very handy features for situations like these.
Most significantly for this shoot, the units can be hooked up to regular sync cables without requiring expensive adapters. This meant that I could fire the flashes using standard radio triggers - the kind that I already had lying around the studio. This gave me a tremendous amount of freedom in placing the flash heads. I could set one unit behind the model to provide backlight and one unit behind myself, facing the model as a key (main) light.
This is an arrangement that could be very difficult to trigger using a line-of-sight infrared system such as those built into dedicated speedlights. Additionally, the Metz flash units provide an audible recycle indicator - they 'beep' when they're ready to fire again. This was a useful feature since I was placing the flashes behind my back and behind car doors, where it would be difficult to see visual LED recycle indicators on the flashes themselves.
Building up the look: This image shows the added background light.
afternoon sun shining on the model's back. This light was metered
at f3.5 @ ISO 200 - about a stop brighter than the ambient light.
A car can be used as a quick and easy set, but photographing a person inside a car does present some difficulties. There are a limited number of places where the photographer can go. Using a large car or one with very adjustable seats can give you more possibilities for situating yourself. There are likewise a limited number of locations where lighting can be placed - nominally, pointing in through the car's exterior windows. To get around this, lights could be boomed in through an open window or held by an assistant if necessary.
For this shoot, I wanted the background light to be directly behind the model, pointing towards the camera. I put the light on a stand aimed through the passenger-side window, behind the model and about two feet away from the car. This created a strongly backlit image, picking up color in the hair and putting lighting artifacts (glare) in the frame.
In order to avoid the temptation to zoom out and capture more of the model in my frame, I used a 50mm prime lens for the shoot (65mm equivalent focal-length after crop factor on my APS-H sensor). This was wide enough to get an acceptable amount of the environment and create some separation between the subject and the background, but not wide enough to cause unflattering wide-angle distortion of the model's features, which would have been a risk if I was using a zoom lens and zoomed out too far.
In progress: adding the key light.
ambient light. This direct, non-diffused light is too flat and washed-out
for the intended mood of the image. Also note the strong shadows cast
behind the model's head; this underscores the fact that we're using
The background light alone did not help to open detail in the model's features, so I added a second flash as a key light to illuminate the model. This flash was about 3 feet behind my shoulder, firing through the open driver's side door of the car. However, the raw flash looked too flat and harsh for my intended treatment. Further, I originally set the flash to be about a stop brighter than the ambient light. This gave the image an obvious 'artificially lit' look.
To remedy this, I lowered the flash's power relative to the ambient light and covered the raw flash bulb with the unit's built-in diffuser. I also moved the flash closer to the model. This slightly increased the size of the flash relative to the subject, which further softened the quality of the light. This diffused light was gentle and closer in intensity to the ambient light, which made the lighting look more believable and natural.
Note that I introduced the background light before adding the key light. The background light has a less significant overall effect on the image; I often find it easier to visualize the contribution of lights going from darkest to brightest. The dim lights take back stage after the big lights are added; if I had started with the key light in place, I might have mistakenly tried to adjust this image by lowering the background light.
The main light has been corrected.
than the ambient light. At this ratio, the key light is providing a strong
fill without overpowering the natural light.
I had fairly limited options as to where the key light could be placed. If the key light were aimed through the windshield or rear window of the car, the model would have had strongly defined shadows on her features. This would not be appropriate for the mood I wanted to achieve. Placing the light so it was facing the model directly provided even illumination with few shadows. This suited the intended mood of the shoot.
It is worth noting that I metered and adjusted the lights manually, rather than relying on TTL (through-the-lens) metering and exposure compensation. This allowed me very precise and deliberate control over the relative power of the key and background lights, even though the background light was sometimes firing directly into my lens.
Technical lighting has been dialed in.
As I wanted the lighting in the image to look natural, I also needed to make sure that the background light (our proxy 'sun') was coming from a plausible angle. This meant raising the light to a location where it didn't seem to be shining through an unlikely gap in the fence, which was otherwise backed by solid vegetation.
|The final look, with post-processing applied. The lens flare artifacts were deliberately left in the image. f2.5, 1/60 @ ISO 200|
Finally, I added some color in post-processing to give the image a warm, pink sunset tone. This was done using a split color filter in Nik Color Efx Pro 3.0. Nik's software allows filter effects to be adjusted in selected areas of an image, such as the skin, with far fewer clicks than traditional masking. In this case, I reduced the effect of the filter on the skin in order to keep the model from getting an atomic suntan.
Beginning to end, this look took about 15 minutes to set up and shoot. Keeping the lighting simple, thinking about the environmental lighting and paying attention to lighting ratios between the flashes and ambient light allowed me to establish a consistent and predictable look very quickly. Best of all, this isn't the type of lighting set that sometimes shows up in photo magazines, where a small truck full of lighting gear and grip equipment is required to get the look. This can easily be done with a pair of external flashes and your neighborhood specialty grocer's alley.
Thomas Park is a fashion / fine art photographer and educator based in Seattle, Washington. To find out more about his work and workshops, please visit http://www.thomasparkphoto.com
Model: Ira Z
All images © 2011, Thomas Park
Sep 26, 2014
Aug 20, 2014
Jun 12, 2014
May 7, 2014
The Everyday Sling might just be the perfect pack for not carrying too much gear, combining comfort with Peak Design's signature modern style.
When the Fujifilm X-T2 arrived, it was more than just a modest upgrade to the already impressive X-T1. While the new X-T3 hasn't changed the overall design of the camera, this model is way more than an upgrade; rather, it's a quantum leap.
The Movie Maker is a compact, motorized slider designed for phones, action cams and small mirrorless cameras. We think it's a fun little kit and a good value proposition for the cost, provided you can work around a few of its weak points.
Nikon's Z7 is the first camera to use the all-new Z-mount, the company's first new full-frame mount since 1959. We've put together our first impressions based on quality shooting time with a pre-production camera - check out what we've found.
What's the best camera for a parent? The best cameras for shooting kids and family must have fast autofocus, good low-light image quality and great video. In this buying guide we've rounded-up several great cameras for parents, and recommended the best.
What's the best camera for shooting landscapes? High resolution, weather-sealed bodies and wide dynamic range are all important. In this buying guide we've rounded-up several great cameras for shooting landscapes, and recommended the best.
What’s the best camera costing over $2000? The best high-end camera costing more than $2000 should have plenty of resolution, exceptional build quality, good 4K video capture and top-notch autofocus for advanced and professional users. In this buying guide we’ve rounded up all the current interchangeable lens cameras costing over $2000 and recommended the best.
|The Lone Photographer by ed rader|
from My Best Photo of the Week
|_ERN9064 by ernesto juarez|
from Shoot yourself ! (with your camera)
|Neighbourhood Watch by Stevie Boy Blue|
from Zoo trip ~ Cute...
GoPro has announced its HERO7 camera lineup. The updated action cameras feature new HyperSmooth and TimeWarp modes, as well as improved video and photo specs.
The latest Samsung midrange smartphone offers a super-wide-angle lens in its triple-camera setup.
The Sony 24mm F1.4 is the latest lens to join the company's premium G Master lineup. We've been shooting with one for a couple of days - here's what you need to know.
Apple released iOS 12 a few days ago and some iPhone X users are less than happy with how the new operating system has made their phones look.
Camera bag manufacturer Lowepro has introduced mark II backpacks for its ProTactic AW range with models that are said to feature an improved handling experience as well as a collection of accessories that can be attached to the outside.
Canon has announced its latest superzoom camera, the PowerShot SX70 HS. Compared to the SX60 that came before it, the SX70 has the same lens but offers a higher resolution EVF, 4K video capture and support for Canon's new CR3 Raw format.
Cosina has announced its eighth lens designed specifically for Sony's E-mount system. The Voigtlander 21mm F3.5 lens is due out October 2018.
Sony has taken the wraps off of its new 24mm F1.4 GM full-frame lens, which the company claims is the lightest in its class. Despite its fast aperture, the 24mm F1.4 is remarkably light, weighing just 445 grams (15.7 ounces). The lens will set you back $1400 when it ships next month.
In this episode of DPReview TV we take a look at Sony's brand new 24mm F1.4 GM lens, a desirable focal length for many photographers. How does it perform? Chris and Jordan give us their first impressions.
We've had a little time to shoot with Sony's new wide/fast prime, both close to home and on the water in San Francisco. Check out our initial sample images.
Fujifilm released a firmware upgrade for its X-T3 mirrorless camera that addresses issues with distortion compensation and the mechanical lock on SD cards.
The app's algorithms have been trained using using 200 million cropping data points from real photographers.
Thanks to a software update, the Loupedeck+ editing console can now be used for video editing.
British photographic engineer MTF Services is claiming the world’s first third-party lens adapters for the new Nikon Z system with a collection of four units designed to allow cinema lenses to be mounted on the mirrorless full frame bodies.
Think Tank Photo has updated its line of heavy-duty rain covers and introduced a new, compact version for emergency situations.
The X-T3 is our first opportunity to analyze what's likely to be Fujifilm's next generation image sensor. Take a look at how it performs next to the competition in our studio test scene.
Canon's new normal is seriously sharp wide open. After shooting with it for a few days, we've prepared a gallery of real-world sample images.
Nikon will cease offering Brazil-based customer service and technical support, though the company stresses that it will still offer technical assistance and warranty repairs for valid warranties.
Two years ago, CatLABS of JP announced a plan to save Packfilm from the dead. Now, it's announced it's giving up its efforts to better focus its resources elsewhere.
The GoPro Fusion is designed to make it easy to capture 360-degree video and stills. We took it out recently on a typically hot Seattle summer day to see what it can do.
We've got our hands on a full-production Nikon Z7 camera and have updated our gallery with additional samples.
A new Kickstarter campaign seeks funding for Chroma Chrono, a programmable RGB camera flash that emits multiple colors during long exposures.
Think Tank Photo has launched a new lineup of six dual-access, water-resistant protective lens cases it calls Lens Case Duo.
Canon and Nikon finally entered the full-frame mirrorless market this summer with the brand-new RF and Z mounts. Now that we've had some time with the cameras, we wanted to revisit our earlier predictions and take stock.
The devices' camera specs look pretty much identical to last year's iPhone X but under the hood a number of important improvements have been made.
Blackmagic Design has announced the public beta of its new Blackmagic RAW video codec. The company says the new format combines the benefits of shooting Raw video with the ease of use and smaller file sizes usually associated with non-Raw video files.
Serif, the company behind the Affinity suite, has announced the latest update for its mobile Photoshop competitor Affinity Photo for iPad.
The Atomos Ninja V external video recorder and monitor will be ready to ship at the end of this month. The 5.2in Ninja V is designed to provide a smaller option, while still offering many of the features of the larger 7-inch models.
Having shot with the camera, spoken to Canon and read the tea leaves, here's what DPR Technical Editor Richard Butler thinks the EOS R tells us about Canon and the RF's mount's future.
After last week's teaser, lighting manufacturer Profoto has announced its 'small big' new product. The B10 is designed to be used as studio flash head but in a very small body, and has a powerful continuous light source for videographers as well.