Variation Facts and Fallacies
1 Variation Facts and Fallacies
Lens sharpness is widely discussed on the internet, so it shouldn’t come as any surprise that lens softness is also a major topic. However, my experience both as a photographer and as the owner of a lens rental business has shown me that much of this discussion is based on a fallacy. So just what is it reasonable to expect from a lens and how doggedly should you pursue the ‘best copy?’
- Noun - "an error in reasoning resulting in a misconception or presumption"
A bit of background
When I started in photography most of the forums I learned from had at least one thread a day about someone’s 'soft lens.' They knew the lens was soft because their camera worked 'fine' with all their other lenses. After a few years of running a rental business, though, I found myself in the following situation three or four times a week:
'The lens you sent me front-focuses, it's not good.'
'OK, we’ll overnight you a replacement.'
Only to find, when the first lens came back, that all our tests suggested it was perfectly fine. And the customer is very happy with the replacement lens - apparently, this one is 'fine.'
So what causes this problem? It's rather simple, actually. The fallacy here is the definition of 'fine.' Most people assume that 'fine' means, 'perfectly calibrated.' It became apparent to me that cameras and lenses are not perfectly calibrated, but rather, they all have some variation. That realisation shouldn’t have been shocking; every manufactured product has variation, why should cameras and lenses be any different?
For the next several years I continued to investigate this issue, writing articles about it as I went. Reading all of them now is an overly-long exercise and I’ve learned a lot since I began writing on this subject. So it seems time to put a summary article together.
|Manufacturing variation affects all lenses from all brands – the only difference is the tolerance levels considered acceptable.|
In most online discussions, things derail when different people understand the same terminology differently. Discussions of lens quality are particularly prone to that, so let me define the terms as I intend to use them.
A soft or bad copy is a copy of lens X that clearly does not perform as well as other copies of lens X. There are bad lenses out there. They happen.
A design choice affects all the copies of Lens X. Every lens has some design choices made that we may not like.
Copy/sample variation is a slight difference that can be detected between different copies of lens X, or different copies of Camera B. Copy variation is detectable, but usually not significant (compared to a bad copy which is always significant).
The Search for the Holy Lens Grail
Before we go further, there are some people that should probably stop reading here. If you ever think 'for $1,500 I demand perfection,' this is not the article for you, it will just get you upset. The laws of physics are not suspended, nor are techniques of manufacturing altered, just because you demand it be so. If you enjoy The Quest for the Perfect Lens and other fantasy games, just move along and save yourself the aggravation of being administered this particular dose of reality.
Why Variation is Inevitable
First, I should mention that the problem has received more attention in recent years, oddly enough, because our equipment has improved so much. A 6MP crop-sensor camera didn’t expose the flaws in a lens that now, a 24MP full-frame camera makes painfully obvious. Better lenses contribute too: when a lens had four really soft corners it was hard to tell if one side was worse than the other. On a newer lens with sharp corners the difference may be instantly obvious.
It’s probably not a coincidence that photographer and blogger Lloyd Chambers brought attention to the fact that camera mounts aren’t always perfectly parallel to the sensor when he was testing Zeiss ZF 21mm lenses on a 24MP Nikon D3x. There's every chance it would not have been apparent if he had been shooting a lesser lens on a lesser camera.
The key thing to realize is that the problem is not limited to one brand, one type of lens, or even just SLR gear. Landscape photographer Joseph Holmes found significant variation in medium format lenses and focusing. Testing website SLR Gear found a batch of 50mm lenses that were all softer on the right side than the left. At Lensrentals we found a group of 300mm f/4 lenses from the same serial number run almost all suffered electrical failures. Why is this so?
Manufacturing tolerances are just that: a range of acceptable values, not an exact point. In other words, what is specified as a 1/4 inch diameter screw may be anything between 0.247 inches and 0.253 inches in diameter (see this chart from an internationally-renowned industrial fastener manufacturer). The machines that make them can’t be more accurate than that at reasonable cost.
Did you know that every time a glass manufacturer makes a run of a given optical glass, the refraction index and dispersion vary a tiny bit? The glass manufacturer furnishes a melt sheet to the lens manufacturer so they can make tiny adjustments in thickness or curvature of that element to compensate for the differences.
The glass is probably a tiny source of variation compared to the other components that make up a lens or camera. In addition to the multiple glass elements, there are clips, shims, and grips that hold them in place within the lens. There are helicoids, barrels, gears, and rings move them around to focus. Electrical motors and circuit boards tell them what to do, and, as Chambers has shown us, even the lens mount that connects the lens to the camera is a source of variation.
|Cross-section of a Zeiss 21mm lens. Note all of the clips, shims, and barrels holding the elements in position.|
Many, if not most, of those components are outsourced to other companies or factories. A change in subcontractor could result in a slightly different part being supplied. Something as simple as a set of ribbon cables more likely to crack or a solder that is slightly less conductive being used on a circuit board could result in significant changes to a camera or lens.
If you delve into the manufacturer’s parts lists (when you can get them) you’ll find they take these variations into account and plan for them within a given tolerance range. For example, if you need to replace the front element of your Nikon 14-24mm lens (part # 1K104-xxx) you need to replace the adjustment washer behind it with one of five specific thicknesses - each copy of the lens requires a slightly different thickness for proper spacing of the front element to focus sharply.
There are numerous other variable-sized spacers and parts for every lens (most lenses have variable thickness spacers in at least three different places). In many lenses even the lens mount comes in several thicknesses or with shims so that the image focuses properly on the sensor. As someone who has to shim lenses fairly frequently, I can assure you it can be done close to perfection, but not perfectly. When a 0.06mm shim is indicated, we often have the choice of 0.05mm or 0.07mm shims - close, but not perfect.
Similarly, the lens must be electronically calibrated. The circuit boards inside each lens with its own AF motor contain adjustment screws to calibrate the frequency and current of the electronic pulses sent to the motor used to move the lens during focusing. Manufacturers don’t build in this adjustment because every lens is exactly the same; they build it in because every lens is slightly different and adjustments are necessary. And by the way: the factory manual gives an acceptable range for the adjustment, something like 150 +/- 2 KHz.
|Frequency and voltage adjustment variable resistors on the printed circuit board inside a Canon EF lens.|
It’s not my purpose to list every source of variation in a given copy of a lens or camera body. They are far too numerous. But just to give an idea of some major ones:
- A lens has eight to 23 elements, each of which may vary slightly in its spacing from the other elements, centering along the axis of the lens, and tilting from right angles to the axis of the lens.
- The focusing and zooming elements must move certain distances front to back within the lens and during their travel their tilt or centering may vary slightly.
- The barrels and helicoids, and various slots in them, must machined so that the elements are not only aligned properly within them, but they are aligned properly with other barrels.
- The lens mount may not be perfectly parallel to the camera’s sensor.
For everything on the list there is a slight variation within an allowable tolerance. You can demonstrate this for yourself if you have some friends (or camera club members) and can get several copies of the same lens. Mount a camera to a tripod and focus on a target that is very visible in live view at 10X magnification. Then, just change from one lens to another and watch the target be a bit off center in different directions with each lens. Just a bit for most lenses, but you might find one that's off target by half of the screen or so.
Camera bodies are no different than lenses with regard to variation, and in fact could be even more problematic. Is the sensor perfectly parallel to the lens mount? Is the AF sensor properly calibrated to the imaging sensor? Is the AF mirror exactly aligned and angled in relation to the AF sensor? The list goes on and on. And in every case the camera is made nearly perfect, but not exactly perfect.
During, and at the end of, the assembly process, the lenses and cameras are tested to make sure they are within the manufacturer’s specifications. If they are out-of-spec and get by quality control, then someone, somewhere gets a truly bad camera or lens. It doesn’t happen frequently, but it happens. When it does, it isn't a subtle call; it's very obvious the lens is bad. In mass-produced elements, quality control is likely to be conducted on a 'sample' basis - only one in every ten or every hundred units will be checked.
But even the cameras and lenses that meet specifications are still going to vary slightly. Many people think, 'I’ll try eight lenses and take the best one.' The reality though is that the only sensible definition of 'best' is 'best with the camera body you are using,'. This is because there is plenty of room for variance in the behavior of bodies, too.
Let’s consider just the lens mount as a theoretical example. First, we say the lens mount of a camera must be parallel to the sensor with a range of +/ - 0.05 degrees (I have no idea what an acceptable range is, I only know that they cannot consistently be made perfectly parallel). Then, let’s say camera A's lens mount has a tilt of 0.04 degrees to the right. Lens #32 has a tilt of 0.04 degrees to the left. The two tilts would cancel each other out, all would be magical, and the owner would write sonnets on the various forums praising his lens.
But let's say he sells his lens to someone whose camera's lens mount has a tilt of 0.03 degrees to the left. The lens and camera now both tilt to the left and the new owner may say, 'the lens you sold me is a bad copy, it’s horribly soft on the sides.'
And this is just tilt. The mounts may also vary in thickness. There is variation, too, in autofocus systems. Certainly more than there is in lens mounts. Through-the-viewfinder manual focus will also vary (you might be surprised to know that viewfinder focusing screens are shimmed by hand). Even exposure metering varies slightly from camera to camera, and requires recalibration if it’s out of specification.
The bottom line is every lens varies slightly, in several respects. And every camera varies slightly too, in a number of different ways. A given lens on four different cameras will behave slightly differently on each of them, and four different copies of the same lens will each perform slightly differently on a given camera body. How differently? Well the short version is you probably will notice the differences if you’re a 'pixel-peeper'. If you use cameras and lenses to take pictures, though, it would be very unlikely you’d notice normal variation, even with large prints. The one exception might be high quality wide aperture lenses because the narrow depth of field may make subtle differences apparent.
|First, Let me check its expiry date. by rajeev22675|
from Best Photo of the Week
|Dairy Way by BodkinsBest|
from Best Astrophotography Landscape #4
YouTube channel Photoshop Cafe has shared a video detailing ten tips and tricks you can do to both fix and speed up Photoshop when it's running slow and sluggish.
It's not going to be the banger of the year, but it'll get a few laughs.
DJI has confirmed its drones won't be affected by the GPS 2019 week rollover.
Dogfish Head Craft Brewery has teamed up with Kodak to release a beer that's capable of doubling as a film developer.
The Diana Instant Square is a retro-inspired camera with manual controls that's fun to shoot in good light, but largely unpredictable in its operation.
Residents of a Paris street plagued by Instagrammers, selfie takers and music video crews are asking the city government for a weekend and evening ban to give them some peace.
The adapter plugs into the Osmo Pocket's USB Type-C port and features a 3.5mm TRS jack to plug in various external microphones.
Checkout allows Instagram users to select products for purchase and make payments directly in the app.
GauGAN as it's known, can create photorealistic images from basic drawings using the power of artificial intelligence.
The EOS RP is Canon's latest full-frame mirrorless camera, with diminutive dimensions and a diminutive price. Find out how it stacks up and get our thoughts in our early review.
Montana judge Dana L. Christensen has ruled the Republican National Committee did not infringe upon the copyright of photographer Erika Peterman after they took a photo from a Democratic candidate's Facebook page without permission and altered it to use in a derogatory promotional mailer.
Nikon has launched updates for three of its programs to address various bugs and glitches that could cause crashes and unwanted results.
LEE Filters has launched the LEE100, its next-generation filter holder that improves the design and looks in all the right places.
With the arrival of some much-needed sunshine and final production firmware for the Panasonic S1, we've been able to get outside and really start putting the camera through its paces.
Importing, culling and tagging photos is about to get a whole lot faster and look a whole lot better with the impending arrival of Photo Mechanic 6.
On its own, the FTZ adapter retails for $250 and when bundled it dropped the cost to just $150. Now, Nikon is offering it for free with all Z6, Z7 purchases in the United States.
Profoto said it spoke with Godox back at Photokina 2018 and continues to contact Godox in an effort to stop it from marketing its V1 light.
Product renders in Italian publication Notebook Italia show an unusual design that conceals all cameras with the help of a slider mechanism.
Canon says its new EF 400mm F2.8L IS III and EF 600mm F4L IS III lenses can suffer from an intermittent flickering when shooting video in M or Av modes with certain cameras.
Leica recently announced the Q2, a digital rangefinder with a fixed 28mm F1.7 lens. It's a heck of a lot of fun to shoot with, but is it right for you? Based on our time with the camera, and its specifications, we've examined how well-suited it is for common photography use-cases.
Now that our Panasonic Lumix S1R has final firmware, we couldn't wait to get out shooting with it - and we also tried the high-res mode, which combines files to get 187 megapixel images. Because sometimes, 47 megapixels just isn't enough.
In this article, travel and landscape photographer Mitch Green encourages us to spend more time in the the field.
the lens lacks any electronics whatsoever and is constructed entirely of glass and metal. Of course, that comes at the expense of weight — this thing weighs in at 1.1kg / 2.43lbs.
Drones can be useful tools in urban areas, where they're utilized for everything from news reporting to building inspections, but flying in these areas requires careful preparation. Here's what you need to know to do so safely.
Hasselblad has released a new cable release and USB double battery charger for its X1D medium format camera .
After a report published by NBC News, Flickr has taken heat for allegedly letting IBM 'scrape' photos for use in its facial recognition datasets. But the problem isn't what it seems on the surface.
Samyang has announced the impending arrival of the AF 85mm F1.4 FE lens for full-frame Sony cameras.
Some Photoshop shortcuts are simple and obvious. Others, not so much. Here are 15 shortcuts that are actually useful.
Twitter has redesigned its in-app camera for easier access from the timeline screen.
Independent cinema lens manufacturer SLR Magic has announced it will offer all of its existing MicroPrime range in the Fujifilm X mount and has even created a Fuji-specific 12mm lens.