Previous page Next page

Flash

The clip-on flash that ships with the Olympus PEN E-PM1 has a guide number of 10m at ISO 200 - giving a range of less than 2m at the long end of the kit zoom at base ISO. Flash exposure is pleasantly well-judged here, and the skin tone rendition is very good.

The E-PM1's flash does have a party trick, though, of being able to act as a wireless controller for compatible external units such as the FL-50R, FL-36R, or recently-announced FL-300R.

Noise Filter and Sharpening

If there's one fault with the E-PM1's JPEGs it's that the default level of noise reduction is rather strong, and can produce rather 'plasticky' images which lack texture and fine detail, especially at high ISO sensitivity settings. These files are fine for making small prints, but viewed up-close, at or close to 100% they look rather over-processed and artificial.

If you don't like this you can, of course, tune your settings to your own personal taste. Noise reduction is, slightly counter-intuitively, set using the 'Noise Filter' control in the Custom G menu (the 'Noise Reduct' option is for long exposures), and you can turn this down to Low or Off to retain detail better. However if you do so, the default sharpening then somewhat accentuates the noise, so you may prefer to turn this down too (note though that sharpening is set individually for each Picture Mode). The examples below give an idea of what's possible.

*Note - the following examples were shot on the E-PL3 as it features the same sensor and JPEG engine as the E-PM1

Olympus 14-42mm, 1/125 F6.3, ISO 800

This ISO 800 shot has pleasing color but the E-PM1's default noise reduction is very aggressive when viewed at 100%. Turning the noise filter off reveals more fine detail, but sharpening now accentuates the noise. This in turn can be mitigated by turning down the sharpening.
Noise Filter = Standard, Sharpness = 0 (Default settings)
Noise filter = Off, Sharpness = 0
Noise filter = Off, Sharpness = -2

Even at relatively low ISO sensitivity settings the Noise Filter can be destructive of fine, low contrast detail (most notably hair), and its smoothing effect over even-toned areas can give a very strange appearance to skin. The example below illustrates this; even at ISO 400 the standard processing gives a very odd look to this portrait when viewed up-close on screen. Turning the noise filter off, and turning down the sharpening to match, results in a far better image for on-screen viewing.

Olympus 14-42mm, 1/125 F5.6, ISO 400.

This example shows the destructive effect of the noise filter on fine low-contrast detail at just ISO 400. Hair has been smoothed, and the skin has taken on a plasticky artificial look. We prefer the rendition with the noise filter turned off and sharpening set to -1, certainly for viewing the image at full size. Individual strands of hair are are now more clearly rendered, while the remaining noise (mainly luminance and finely-grained in character) isn't at all unpleasant.
100% crop: Noise Filter = Standard, Sharpness = 0
100% crop: Noise Filter = Off, Sharpness = -1

Antishock

Olympus's Antishock setting can come in quite handy when shooting on a tripod. Located in the Custom E menu, the Antishock option is available in increments from 1/8 second to 30 seconds. Antishock works to minimize shutter-generated vibrations by delaying the time between the shutter's closing and opening cycles as the camera switches from a live view preview to taking a picture, then back to live view. The following samples are taken from the E-PL3.

ISO 200, f/6.3 @ 1/100s
IS off
With IS turned off, and the sensor locked in position, the shutter causes a slight vibration which results in a slightly blurry image.
ISO 200, f/6.3 @ 1/100s
IS off with Antishock enabled (4sec)
This 100% crop shows that using Antishock yields a sharper image, if only by a small degree.

In the examples above, the sharpest results are obtained when disabling IS and activating Antishock. We've highlighted this issue with the most critical test for sharpness at our disposal - our image resolution chart. This hardly represents real-world use and the differences become evident most clearly in side-by-side comparisons as the ones you see above. However, should you require absolute, critical sharpness and resolution when shooting on a tripod, you're best served by making sure IS is disabled and activating Antishock. We consistently found four seconds to be a sufficient setting for Antishock, as opposed to higher values.

Overall Image Quality/Specifics

On the whole, the PEN Mini offers very good image quality in both JPEG and raw modes. In typical Olympus fashion it turns out well-exposed, attractive images with lovely color rendition time after time. Overall its output is all but identical to its more expensive sister models, the E-P3 and E-PL3, and that's no bad thing at all.

The E-PM1's metering is generally very reliable, which means that badly-blown highlights are relatively rare (of course you can easily keep an eye on this using either the live histogram or exposure warning display modes, and tweak the exposure compensation appropriately). White balance is also well-judged, with skin tones rendered naturally. To this end there's even an option to bias the Auto WB towards producing warmer colors in the Custom G menu.

We've long been big fans of Olympus's color rendition, from either out-of-camera JPEGs or raw using the supplied conversion software. The PEN Mini continues in this tradition, with the default Natural mode delivering attractive, saturated colors. However if you shoot in iAuto mode, the camera will use its i-Enhance picture mode that can look distinctly cartoonish - some users may well like this, but on the whole we're not too keen on it.

The one area where the E-PM1 falls a little behind the competition, though, is in terms of high ISO noise; its 12Mp sensor is now distinctly lagging behind newer APS-C sensors in this regard. It still produces quite acceptable results up to about ISO3200, but going any higher becomes distinctly problematic (and ISO 12800 is so noisy as to be nearly unusable).

However it's worth bearing in mind that the E-PM1's in-body image stabilization can offset this to a degree; it allows you to shoot at slower shutter speeds and therefore lower ISOs than would otherwise be possible (as long as the subject isn't moving too fast, at which point blur can become a problem). And unlike other systems that rely on in-lens stabilization, it works with any lens mounted on the camera, including manual lenses connected via an adapter.

Previous page Next page
116
I own it
6
I want it
52
I had it
Discuss in the forums

Comments